Microe OPS Series Manual do Utilizador

Page 1RoHSSensor InstallationManual and ReferenceGuideMicroE Systems • 125 Middlesex Turnpike • Bedford, MA 01730 • USA www.microesystems.co

Page 10Sensor Head Installation (Top Mount Configuration)OPS™Series EncodersSensor Mounting Orientation and TolerancesAxis diagram.OPS Top Mount Confi

Page 11Sensor Head Installation (Top Mount Configuration)OPS™Series Encoders1.Verify Sensor Mounting Surface HeightRefer to the OPS interface drawing

Page 12Sensor Alignment - by Alignment ToolOPS™Series Encoders, Side and Top Mount ConfigurationsBe sure the source power is off before connecting the

Page 13Sensor Alignment - by Alignment ToolOPS™Series Encoders, Side and Top Mount Configurations2.AlignmentConnect the USB cable to the Alignment Too

Page 141.Press the Alignment Tool Cal button to start. (Be sure the sensor has been aligned to the scale, across theentire length.) Both the Alignment

Page 15Sensor Alignment and Calibration - by SmartPrecision™ II SoftwareOPS™Series Encoders, Side and Top Mount ConfigurationsInstall the OPS SmartPre

Page 16Sensor Alignment - by SmartPrecision™ II SoftwareOPS™Series Encoders, Side and Top Mount ConfigurationsConnect the encoder to the Alignment Too

Page 17Sensor Calibration - by SmartPrecision™ II SoftwareOPS™Series Encoders, Side and Top Mount Configurations1. Click appropriatecheckboxes beforec

Page 18Sensor Calibration - by SmartPrecision™ II SoftwareOPS™Series Encoders, Side and Top Mount Configurations7. Calibrationcomplete.6. Move thesens

Page 19Appendix ASpecificationsAgency Standards Conformance: In accordance withElectromagnetic Compatibility Directive 2004/108/EC:EN 55011:2007 EN

Page 2Table of ContentsOPS™Sensor InstallationIntroductionIntroduction (Precautions, Patents, Manual Revisions) ...

Page 20Appendix BWiring DiagramsConnector Pin Configuration     !!5!'!    

JacketAluminumPolyesterShiedBraidedShieldPage 21Appendix CInterface Cable RequirementsOPS SeriesSignal Twisted PairA+ Pair 1A-B+ Pair 2B-Index+ Pair 3

Page 22The OPS Series is RS-422 compatible. Encoder signals are “sending end terminated.” Therefore customerreceiving terminations are not required. I

Page 23Appendix ETroubleshootingProblemThe Sensor LED indicator won’t turn on.Solution• Make sure that the OPS Series electronics’ 15-pin D-sub connec

Page 24Appendix FOrder GuideHow to OrderAll specifications subject to change.PurePrecision™ Marker Tape IIHPMT – N – A –L– 5000 –II = Individual Lengt

Page 25Contacting MicroEMicroE Systems is a world leader in optical encoder technology withoffices in major industrial centers around the globe.To lea

Page 3LASER SAFETY INFORMATION: OPS SeriesThis product is sold solely for use as a component (or replacement) in an electronic product; therefore it i

Page 4Recommendations for Power; Installation ConsiderationsOPS™Sensor Installation1.Recommendations for PowerOPS™encoders require a minimum of 4.75VD

Page 5System OverviewOPS™Series EncodersItems Required for OPS Encoder Installation• Hex wrench (M3.5 for Side Mount, 5/64" or M2.5 for Top Mount

Page 6System Overview, OPS Side MountOPS™Sensor InstallationOPSTMSeries, Side Mount ConfigurationSystem View Expanded ViewScale (shown mounted on a li

Page 7Sensor Head Installation (Side Mount Configuration)OPS™Series EncodersSensor Mounting Orientation and TolerancesAxis diagram.OPS Side Mount Conf

Page 8Sensor Head Installation (Side Mount Configuration)OPS™Series Encoders2.Verify Sensor Mounting Surface HeightRefer to the OPS interface drawing

Page 9OPSTMSeries, Top Mount ConfigurationSystem View Expanded ViewSensor(shown attached on a linear slide basewith mounting bracket)Scale (shown moun